CVE-2026-79982

Out-of-bounds write in the USB Bluetooth HCI transport class when a controller-to-host HCI packet exceeds the bulk endpoint maximum packet size

Published Oct 23, 2026 CVSS 3.1 · 8.8 High EPSS < 1% KEV · Not listed
Description
The Bluetooth HCI USB transport class of the new USB device stack, subsys/usb/device_next/class/bt_hci.c, copies every controller-to-host HCI packet into a USB transfer buffer before enqueuing it on an endpoint. bt_hci_tx_sync_in() allocated that buffer from bt_hci_ep_pool, a fixed pool whose slots are only USBD_MAX_BULK_MPS bytes (64 on full-speed-only builds), and then performed net_buf_add_mem(buf, bt_buf->data, bt_buf->len) with no length check. HCI event and ACL buffers are sized by CONFIG_BT_BUF_EVT_RX_SIZE and CONFIG_BT_BUF_ACL_RX_SIZE and can be far larger, so the copy runs past the end of the 64-byte slot into the adjacent slots and into whatever follows the statically allocated pool.

The device runs the local Bluetooth controller in raw HCI mode (CONFIG_BT_HCI_RAW), so the oversized packets originate over the air. With the HCI buffer sizes recommended for full-featured controllers, an unauthenticated attacker within Bluetooth range can supply the overflowing bytes: a connected peer that negotiates Data Length Extension can send ACL fragments up to CONFIG_BT_CTLR_DATA_LENGTH_MAX bytes, and an attacker that merely broadcasts extended advertising data reaches the same path through LE Extended Advertising Report events, which the controller fragments only to CONFIG_BT_BUF_EVT_RX_SIZE. In the stock configuration the overflow is already reached without any radio traffic: the mandatory Read Supported Commands command-complete event is 70 bytes and overruns the 64-byte slot by six bytes on every host initialization.

Because net_buf_add_mem() validates tailroom only through an assertion unless CONFIG_NET_BUF_HARDENING is enabled, builds with CONFIG_ASSERT=n — the usual production setting — silently corrupt memory adjacent to the USB buffer pool with attacker-chosen contents, which on a target without memory protection between subsystems can lead to arbitrary code execution. Builds with assertions enabled fail the assertion instead and panic, giving a remotely triggerable denial of service. The fix introduces a separate bt_hci_tx_pool sized to MAX(BT_BUF_ACL_RX_SIZE, BT_BUF_EVT_RX_SIZE) for the controller-to-host direction while leaving the host-to-device pool at the endpoint packet size, which is already bounds-checked during reassembly.

Remediation

No solution or workaround provided in the CVE record

Tracking

Sign in to view the affected projects.

Advisories

No advisories available
History
Type Values Removed Values Added
Metrics ssvc

{'options': {'Automatable': 'no', 'Exploitation': 'none', 'Technical Impact': 'total'}, 'version': '2.0.3'}

Type Values Removed Values Added
First Time appeared Zephyrproject
Zephyrproject zephyr
Vendors & Products Zephyrproject
Zephyrproject zephyr
Type Values Removed Values Added
Description The Bluetooth HCI USB transport class of the new USB device stack, subsys/usb/device_next/class/bt_hci.c, copies every controller-to-host HCI packet into a USB transfer buffer before enqueuing it on an endpoint. bt_hci_tx_sync_in() allocated that buffer from bt_hci_ep_pool, a fixed pool whose slots are only USBD_MAX_BULK_MPS bytes (64 on full-speed-only builds), and then performed net_buf_add_mem(buf, bt_buf->data, bt_buf->len) with no length check. HCI event and ACL buffers are sized by CONFIG_BT_BUF_EVT_RX_SIZE and CONFIG_BT_BUF_ACL_RX_SIZE and can be far larger, so the copy runs past the end of the 64-byte slot into the adjacent slots and into whatever follows the statically allocated pool. The device runs the local Bluetooth controller in raw HCI mode (CONFIG_BT_HCI_RAW), so the oversized packets originate over the air. With the HCI buffer sizes recommended for full-featured controllers, an unauthenticated attacker within Bluetooth range can supply the overflowing bytes: a connected peer that negotiates Data Length Extension can send ACL fragments up to CONFIG_BT_CTLR_DATA_LENGTH_MAX bytes, and an attacker that merely broadcasts extended advertising data reaches the same path through LE Extended Advertising Report events, which the controller fragments only to CONFIG_BT_BUF_EVT_RX_SIZE. In the stock configuration the overflow is already reached without any radio traffic: the mandatory Read Supported Commands command-complete event is 70 bytes and overruns the 64-byte slot by six bytes on every host initialization. Because net_buf_add_mem() validates tailroom only through an assertion unless CONFIG_NET_BUF_HARDENING is enabled, builds with CONFIG_ASSERT=n — the usual production setting — silently corrupt memory adjacent to the USB buffer pool with attacker-chosen contents, which on a target without memory protection between subsystems can lead to arbitrary code execution. Builds with assertions enabled fail the assertion instead and panic, giving a remotely triggerable denial of service. The fix introduces a separate bt_hci_tx_pool sized to MAX(BT_BUF_ACL_RX_SIZE, BT_BUF_EVT_RX_SIZE) for the controller-to-host direction while leaving the host-to-device pool at the endpoint packet size, which is already bounds-checked during reassembly.
Title Out-of-bounds write in the USB Bluetooth HCI transport class when a controller-to-host HCI packet exceeds the bulk endpoint maximum packet size
Weaknesses CWE-787
References
Metrics cvssV3_1

{'score': 8.8, 'vector': 'CVSS:3.1/AV:A/AC:L/PR:N/UI:N/S:U/C:H/I:H/A:H'}

Weaknesses

Sources

Status
PUBLISHED
Assigner
zephyr
Published
Updated
Nov 4, 2026, 5:01 AM
Reserved
Aug 25, 2026, 4:06 PM
Status
Awaiting Analysis
Published
Oct 23, 2026, 8:17 PM
Modified
Nov 4, 2026, 5:19 AM